Description

Technical Parameters

Advantages

★Adopt open drying mode, no waste gas waste heat emission, no noise pollution, is a highly efficient and environmentally friendly products.

★Drying temperature 15 ~ 43 ℃, cold / hot air drying mode, fully meet the drying of various types of aquatic products, replacing the traditional steam, electric heat, hot air and other drying.

★Improve the drying quality of aquatic products, product color, luster to achieve high quality standards, better than the sun mode.

★Drying process to achieve a class of health conditions standards, the product fully suitable for export level requirements.

★Advanced ventilation and air inlet drying system design, to achieve ventilation and air requirements and stable drying conditions.

High temperature heat pump principle for steam condensation heat recovery, no waste heat emission, saving operating costs, compared with coal-fired method can save more than 40% of the cost, compared with fuel oil, electric heating can save more than 60% of the cost.

★Compared with the traditional dryer method, it can save more than 50% energy and shorten the drying cycle.

★Advanced drying process and design of drying room, intelligent automatic control system.

★According to the product set different temperature program curve (variable temperature drying), drying conditions are stable, uniform, good quality.

★Easy to use management, equipment without full-time manual management, fully automatic operation.

★Setting multiple safety protection functions: phase sequence protection, phase failure protection, overload protection, high voltage protection, low voltage protection, etc.

121

Unit Model		10PL	12PL	15PV	25PV	50PU
Unit Model		DKXRK-36Ⅱ/LH	DKXRK-44Ⅱ/LH	DKXRK-54Ⅱ/VH	DKXRK-90Ⅱ/VH	DKXRK-180Ⅱ/UH
Power supply specifications		380V/3N~50Hz	380V/3N~50Hz	380V/3N~50Hz	380V/3N~50Hz	380V/3N~50Hz
Rated heating Dry bulb 20 degrees Wet bulb 15 degrees	Nominal heat production(KW)	36	46	54	90	180
	Nominal heating input power (KW)	8.7	10.9	12.8	21.4	42.8
	Nominal current(A)	19.6	21.8	25.6	42.8	85.6
	Energy efficiency ratio (W/W)	4.1	4.2	4.2	4.2	4.2
Outlet air temperature	Rated heating return air temperature ℃	50	50	50	50	50
Outlet air temperature	Maximum heating air outlet temperature ℃	75	75	75	75	75
Function		Heating and drying	Heating and drying	Heating and drying	Heating and drying	Heating and drying
Waterproof grade		IPX4	IPX4	IPX4	IPX4	IPX4
Refrigerant (charge quantity)	R134A	2*5	2*5	2*5.2	2*10	4*10
Waterway side	Type	Set exchange	Set exchange	Set exchange	Set exchange	High efficiency tank
	Inlet and outlet water pipe size	1.5"\DN40 internal teeth	1.5"\DN40 internal teeth	1"\DN25 internal teeth	2"\DN50 internal teeth	3"\DN80 internal teeth
	Circulating water flow rate(m³\h)	7	7	5	15.5	31
	Main pipe diameter	PPR50/40 iron pipe	PPR50/40 iron pipe	PPR32/25 iron pipe	63PPR/50 iron pipe	90PPR/80 iron pipe
	Water-side pressure loss (kPa)	60	60	50	85	85
Power cord specifications		4 square copper wire	4 square copper wire	4 square copper wire	10 square copper wire	20 square copper wire
Dimension		14247851210	14247851210	16009202000	203011002120	230013002390
Net weight of the unit(kg)		305	340	200	730	1500
Gross weight of the unit(kg)		340	380	230	780	1550
Operating noise(dB(A))		<65dB(A)	<65dB(A)	<65dB(A)	<72dB(A)	<78dB(A)
Remarks	1. Rated test conditions: ambient dry and wet bulb temperature is 20℃ /15℃ unit return air 50℃/70%. 2. Use ambient temperature:-25~43℃ 3. The size of the inner machine depends on the customer's demand. 4. If the specification changes due to product improvement, the nameplate reference The number shall prevail.

Installation Process

1. Choose a proper location: Choosing a location for the dryer installation should be in a well-ventilated area that will prevent moisture and heat build-up. Also, it is recommended to install it far from the waste disposal area so that the waste will not contaminate the equipment.

2. Install the power system: Select the appropriate power cord according to the power of the dryer. Connect the power cord to the power system inside the dryer.

3. Install the heat source system: install the heater and burner to ensure the whole system can work properly. It is also necessary to install gas valves and meters to ensure the safety and stability of the gas.

4. Install the conveyor system: If the grain enters the dryer through the conveyor belt, the conveyor belt support and rollers need to be installed.

5. Install the main body of the dryer: Before installing the main body of the dryer, you need to do some preparation work first, such as cleaning the inside of the dryer cavity. Then, connect the main body of the dryer to the heat source system and the conveyor system.

6. Install the control system: To ensure that the dryer works reliably, a control system needs to be installed to monitor and adjust the various parameters of the dryer. The control system includes thermometer, hygrometer, inverter and PLC controller, etc.

7. Perform commissioning and testing: After installation, precise commissioning and testing of the dryer's functions are required to confirm that all equipment is functioning properly before production can begin.

8. Training and maintenance: In order to ensure the performance and life of the dryer, operators need to be trained in operation, maintenance and servicing to enhance their safety awareness and maintenance skills. Also, regular maintenance and inspection of the dryer is required to ensure its long-term effective operation.